View XP-G2_7762530.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product family data sheet copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 cld-ds51 rev 9a cree ? xlamp ? XP-G2 leds product description the xlamp ? XP-G2 le d builds on the unprecedented performance of the original xp-g by increasing lumen output up to 20% while providing a single die l e d point source for precise optical control. the XP-G2 l e d shares the same footprint as the original xp-g, providing a seamless upgrade path and shortening the design cycle. xlamp XP-G2 l e ds are the ideal choice for lighting applications where high light output and maximum effcacy are required, such as l e d light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting. features ? available in white, outdoor white and 80-, 85- and 90-cri white ? ansi-compatible chromaticity bins ? binned at 85 c ? maximum drive current: 1500 ma ? low thermal resistance: 4 c/w ? wide viewing angle: 115 ? unlimited foor life at 30 oc/85% rh ? refow solderable - jedec j- std-020c ? e lectrically neutral thermal path ? rohs- and reach -compliant ? ul-recognized component (e349212) www .cree.com/xlamp table of contents characteristics .......................... 2 flux characteristics .................... 3 relative spectral power distribution ............................... 5 relative flux vs. junction temperature ............................. 5 e lectrical characteristics ............. 6 relative flux vs. current ............ 6 relative chromaticity vs current and temperature ....................... 7 typical spatial distribution .......... 8 thermal design ......................... 8 refow soldering characteristics .. 9 notes ...................................... 10 mechanical dimensions .............. 11 tape and reel .......................... 12 packaging ................................ 13
2 characteristics characteristics unit minimum typical maximum thermal resistance, junction to solder point c/w 4 viewing angle (fwhm) degrees 115 temperature coeffcient of voltage mv/c -1.8 esd withstand voltage (hbm per mil-std-883d) v 8000 dc forward current ma 1500 reverse voltage v 5 forward voltage (@ 350 ma, 85 c) v 2.8 3.15 forward voltage (@ 700 ma, 85 c) v 2.9 forward voltage (@ 1000 ma, 85 c) v 3.0 forward voltage (@ 1500 ma, 85 c) v 3.1 le d junction temperature c 150 copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
3 flux characteristics (t j = 85 c) the fo llowing table provides several base order codes for xlamp XP-G2 l e ds. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. color cct range base order codes min. luminous flux @ 350 ma calculated minimum luminous flux (lm)** @ 85 c order code min. max. group flux (lm) @ 85 c flux (lm) @ 25 c* 700 ma 1.0 a 1.5 a cool white 5000 k 8300 k r3 122 138 223 297 402 xpgbwt-l1-0000-00f51 r4 130 147 237 316 429 xpgbwt-l1-0000-00g51 r5 139 158 254 338 458 xpgbwt-l1-0000-00h51 s2 148 168 271 360 488 xpgbwt-l1-0000-00j51 outdoor white 3200 k 5300 k r2 114 129 208 277 376 xpgbwt-01-0000-00 ec2 r3 122 138 223 297 402 xpgbwt-01-0000-00fc2 r4 130 147 237 316 429 xpgbwt-01-0000-00gc2 r5 139 158 254 338 458 xpgbwt-01-0000-00hc2 neutral white 3700 k 5300 k q5 107 121 195 260 353 xpgbwt-l1-0000-00d e4 r2 114 129 208 277 376 xpgbwt-l1-0000-00 ee4 r3 122 138 223 297 402 xpgbwt-l1-0000-00f e4 r4 130 147 237 316 429 xpgbwt-l1-0000-00g e4 80-cri white 2600 k 4300 k q4 100 113 182 243 330 xpgbwt-h1-0000-00ce7 q5 107 121 195 260 353 xpgbwt-h1-0000-00de7 r2 114 129 208 277 376 xpgbwt-h1-0000-00ee7 r3 122 138 223 297 402 xpgbwt-h1-0000-00fe7 r4 130 147 237 316 429 xpgbwt-h1-0000-00ge7 warm white 2600 k 3700 k q4 100 113 182 243 330 xpgbwt-l1-0000-00c e7 q5 107 121 195 260 353 xpgbwt-l1-0000-00d e7 r2 114 129 208 277 376 xpgbwt-l1-0000-00 ee7 r3 122 138 223 297 402 xpgbwt-l1-0000-00f e7 r4 130 147 237 316 429 xpgbwt-l1-0000-00g e7 copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds notes : ? cree maintains a tolerance of 7% on fux and power measurements, 0.005 on chromaticity (ccx, ccy) measurements and 2 on cri measurements. ? typical cri for cool white (5000 k - 8300 k cct) is 70. ? typical cri for neutral white (3700 k - 5300 k cct) is 75. ? typical cri for outdoor white (4000 k - 5300 k cct) is 70. ? typical cri for warm white (2600 k - 3700 k cct) is 80. ? minimum cri for 80-cri white is 80. ? minimum cri for 85-cri white is 85. ? minimum cri for 90-cri white is 90. ? flux values @ 25 c are calculated and for reference only. ** calculated fux values at 700 ma, 1 a and 1.5 a are for reference only.
4 color cct range base order codes min. luminous flux @ 350 ma calculated minimum luminous flux (lm)** @ 85 c order code min. max. group flux (lm) @ 85 c flux (lm) @ 25 c* 700 ma 1.0 a 1.5 a 85-cri white 2600 k 3200 k p3 73.9 83.8 135 180 244 xpgbwt-p1-0000-008 e7 p4 80.6 91.4 147 196 266 xpgbwt-p1-0000-009 e7 q2 87.4 99.1 160 213 288 xpgbwt-p1-0000-00a e7 q3 93.9 106 172 228 310 xpgbwt-p1-0000-00b e7 90-cri white 2600 k 3200 k p3 73.9 83.8 135 180 244 xpgbwt-u1-0000-008 e7 p4 80.6 91.4 147 196 266 xpgbwt-u1-0000-009 e7 q2 87.4 99.1 160 213 288 xpgbwt-u1-0000-00a e q3 93.9 106 172 228 310 xpgbwt-u1-0000-00b e7 flux characteristics (t j = 85 c) - continued copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds notes : ? cree maintains a tolerance of 7% on fux and power measurements, 0.005 on chromaticity (ccx, ccy) measurements and 2 on cri measurements. ? typical cri for cool white (5000 k - 8300 k cct) is 70. ? typical cri for neutral white (3700 k - 5300 k cct) is 75. ? typical cri for outdoor white (4000 k - 5300 k cct) is 70. ? typical cri for warm white (2600 k - 3700 k cct) is 80. ? minimum cri for 80-cri white is 80. ? minimum cri for 85-cri white is 85. ? minimum cri for 90-cri white is 90. ? flux values @ 25 c are calculated and for reference only. ** calculated fux values at 700 ma, 1 a and 1.5 a are for reference only.
5 relative spectral power distribution relative flux vs. junction temperature (i f = 350 ma) relative spectral power 0% 20% 40% 60% 80% 100% 380 430 480 530 580 630 680 730 780 relative radiant power (%) wavelength (nm) 5000k - 8300k cct 3700k - 5000k cct 2600k - 3700k cct relative flux output vs. junction temperature 0% 20% 40% 60% 80% 100% 120% 25 50 75 100 125 150 relative luminous flux junction temperature (oc) copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
6 electrical characteristics (t j = 85 c) relative flux vs. current (t j = 85 c) electrical characteristics (tj = 25oc) 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 2.50 2.75 3.00 3.25 forward current (ma) forward voltage (v) relative intensity vs. current (tj = 25oc) 0% 50% 100% 150% 200% 250% 300% 350% 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 relative luminous flux (%) forward current (ma) copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
7 relative chromaticity vs current and temperature (warm white*) * warm white xlamp XP-G2 l e ds have a typical cri of 80. delta cct vs. current - 0.020 - 0.015 - 0.010 - 0.005 0.000 0.005 0.010 0.015 0.020 100 300 500 700 900 1100 1300 1500 current (ma) ccx ccy delta cct vs temp - 0.020 - 0.015 - 0.010 - 0.005 0.000 0.005 0.010 0.015 0.020 25 50 75 100 125 150 tsp ( c) ccx ccy copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
8 typical spatial distribution thermal design the maximum forward current is determined by the thermal resistance between the l e d junction and ambient. it is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. typical spatial radiation pattern 0% 20% 40% 60% 80% 100% - 100 - 80 - 60 - 40 - 20 0 20 40 60 80 100 relative luminous intensity (%) angle (o) thermal design cool white 0 200 400 600 800 1000 1200 1400 1600 0 20 40 60 80 100 120 140 maximum current (ma) ambient temperature (oc) rj - a = 10 c/w rj - a = 15 c/w rj - a = 20 c/w rj - a = 25 c/w copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
9 reflow soldering characteristics in testing, cree has found xlamp XP-G2 leds to be compatible with jedec j-std-020c, using the parameters listed below. as a general guideline, cree recommends that users follow the recommended soldering profle provided by the manufacturer of solder paste used. note that this general guideline may not apply to all pcb designs and confgurations of refow soldering equipment. profle feature lead-based solder lead-free solder average ramp-up rate (ts max to tp) 3 c/second max. 3 c/second max. preheat: temperature min (ts min ) 100 c 150 c preheat: temperature max (ts max ) 150 c 200 c preheat: time (ts min to ts max ) 60-120 seconds 60-180 seconds time maintained above: temperature (t l ) 183 c 217 c time maintained above: time (t l ) 60-150 seconds 60-150 seconds peak/classifcation temperature (tp) 215 c 260 c time within 5 c of actual peak temperature (tp) 10-30 seconds 20-40 seconds ramp-down rate 6 c/second max. 6 c/second max. time 25 c to peak temperature 6 minutes max. 8 minutes max. note: all temperatures refer to topside of the package, measured on the package body surface. t p t l temperature time t 25?c to peak preheat ts t s t p 25 ramp-down ramp-up critical zone t l to t p ts max ts min copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
10 notes lumen maintenance projections cree now uses standardized i e s lm-80-08 and tm-21-11 methods for collecting long-term data and extrapolating led lumen maintenance. for information on the specifc lm-80 data sets available for this led, refer to the public lm-80 results document . please read the long-term lumen maintenance application note for more details on crees lumen maintenance testing and forecasting. please read the thermal management application note for details on how thermal design, ambient temperature, and drive current affect the l e d junction temperature. moisture sensitivity in testing, cree has found xlamp XP-G2 leds to have unlimited foor life in conditions 30 oc/85% relative humidity (rh). moisture testing included a 168-hour soak at 85 oc/85% rh followed by 3 refow cycles, with visual and electrical inspections at each stage. cree recommends keeping xlamp l e ds in their sealed moisture-barrier packaging until immediately prior to use. cree also recommends returning any unused l e ds to the resealable moisture-barrier bag and closing the bag immediately after use. r o hs c ompliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the product documentation sections of www.cree.com . reac h c ompliance reach substances of high concern (svhcs) information is available for this product. since the european chemical agency (echa) has published notice of their intent to frequently revise the svhc listing for the foreseeable future, please contact a cree representative to insure you get the most up-to-date r e ach declaration. re ach banned substance information (reach article 67) is also available upon request. ul r ecognized c omponent level 4 enclosure consideration. the led package or a portion thereof has been investigated as a fre and electrical enclosure per ansi/ul 8750. vision advisory claim warning: do not look at exposed lamp in operation. e ye injury can result. for more information about le ds and eye safety, please refer to the led e ye safety application note . copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
11 mechanical dimensions (t a = 25 c) all measurements are .13 mm unless otherwise indicated. .60 1.60 1.65 .65 2.00 3.45 3.45 .40 .60 3.20 1.20 .40 .40 3.20 (hatched area is opening) recommended stencil pattern recommended pcb solder pad 3.30 3.30 1.30 .50 .50 .50 .40 2.30 3.30 .50 1.30 .50 .73 2.6 side view top view bottom view all measurements are .13mm unless otherwise indicated anode size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 .73 .65 r 1.53 3.30 3.30 2.30 .50 1.30 2.26 1 / 1 22.000 a 2610-00024 outline drawing xpg g2 05/09/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 .73 .65 r 1.53 3.30 3.30 2.30 .50 1.30 2.26 1 / 1 22.000 a 2610-00024 outline drawing xpg g2 05/09/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 .73 .65 r 1.53 3.30 3.30 2.30 .50 1.30 2.26 1 / 1 22.000 a 2610-00024 outline drawing xpg g2 05/09/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 .73 .65 r 1.53 3.30 3.30 2.30 .50 1.30 2.26 1 / 1 22.000 a 2610-00024 outline drawing xpg g2 05/09/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 .50 .50 .40 1.30 3.30 3.30 1.15 .65 1.65 .50 1.20 .60 .60 3.20 1.60 3.20 .40 .40 .40 3.45 3.45 .73 .65 r 1.53 3.30 3.30 2.30 .50 1.30 2.26 1 / 1 22.000 a 2610-00024 outline drawing xpg g2 05/09/12 d. cronin revisons rev description by date app'd recommended pcb solder pad recommended stencil pattern (hatched area is opening) anode copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
12 tape and reel all cree carrier tapes conform to eia-481d, automated component handling systems standard. all dimensions in mm. size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) loaded pockets (1000 lamps) leader 400mm (min.) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) 12.0 +.3 -.0 1.75 .10 4.1 8.1 2.5.1 1 / 1 3.000 b 2402-00014 xp hew loading spec -- -- -- -- -- -- 11/29/10 d. cronin revisons rev description by date app'd b added cathode and anode note reoriented device dc 2/26/12 end start user feed direction cathode side anode side user feed direction 7" 1.5 .1 13mm pocket tape carrier tape 13 61 12.40 0 + 2.00 measured at hub 12.40 measured at inside edge 16.40 sheet 1 of 1 1:2 2400-00005 size title rev. c drawing no. date date date check final protective finish material approved drawn by third angle projection .x 0.3 x 2 .xx .10 .x .25 for sheet metal parts only .xx .13 x 1 unless otherwise specified dimensions are in millimeters & before finish. tolerance unless specified: scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 361-4770 4600 silicon drive durham, n.c 27703 notice cree confidential. this plot and the information contained within are the proprietary and confidential information of cree, inc. this plot may not be copied, reproduced or disclosed to any unauthorized person without the written consent of cree, inc. reel, 7" x 12mm wide b liudezhi 2012/5/25 +/- 0.5 ps 190 ????1? ??e (c) by foxit software company, 2004 foxit pdf editor ?- od 7.5'' 13 61 12.40 0 + 2.00 measured at hub 12.40 measured at inside edge 16.40 sheet 1 of 1 1:2 2400-00005 size title rev. c drawing no. date date date check final protective finish material approved drawn by third angle projection .x 0.3 x 2 .xx .10 .x .25 for sheet metal parts only .xx .13 x 1 unless otherwise specified dimensions are in millimeters & before finish. tolerance unless specified: scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 361-4770 4600 silicon drive durham, n.c 27703 notice cree confidential. this plot and the information contained within are the proprietary and confidential information of cree, inc. this plot may not be copied, reproduced or disclosed to any unauthorized person without the written consent of cree, inc. reel, 7" x 12mm wide b liudezhi 2012/5/25 +/- 0.5 ps 190 ????1? ??e (c) by foxit software company, 2004 foxit pdf editor ?- od 7.5'' y y x x ref 0.59 w f(iii) p1 d1 1.5 min. bo ao r 0.2 typical ref 4.375 ko other material available. (iv) (iii) (ii) (i) hole to centerline of pocket. measured from centerline of sprocket holes is 0.20. cumulative tolerance of 10 sprocket to centerline of pocket. measured from centerline of sprocket hole section y-y section x-x 2.0 0.05 (i) p2 1.55 0.05 do 4.0 0.1 (ii) po 1.75 0.1 e1 0.30 0.05 t ref r 2.24 2.40 ko +0.0/-0.1 3.70 1 w f p +/- 0.05 +/- 0.1 +0.3/-0.1 5.50 8.00 12.00 ao 3.70 +/- 0.1 bo +/- 0.1 y y x x ref 0.59 w f(iii) p1 d1 1.5 min. bo ao r 0.2 typical ref 4.375 ko other material available. (iv) (iii) (ii) (i) hole to centerline of pocket. measured from centerline of sprocket holes is 0.20. cumulative tolerance of 10 sprocket to centerline of pocket. measured from centerline of sprocket hole section y-y section x-x 2.0 0.05 (i) p2 1.55 0.05 do 4.0 0.1 (ii) po 1.75 0.1 e1 0.30 0.05 t ref r 2.24 2.40 ko +0.0/-0.1 3.70 1 w f p +/- 0.05 +/- 0.1 +0.3/-0.1 5.50 8.00 12.00 ao 3.70 +/- 0.1 bo +/- 0.1 y y x x ref 0.59 w f(iii) p1 d1 1.5 min. bo ao r 0.2 typical ref 4.375 ko other material available. (iv) (iii) (ii) (i) hole to centerline of pocket. measured from centerline of sprocket holes is 0.20. cumulative tolerance of 10 sprocket to centerline of pocket. measured from centerline of sprocket hole section y-y section x-x 2.0 0.05 (i) p2 1.55 0.05 do 4.0 0.1 (ii) po 1.75 0.1 e1 0.30 0.05 t ref r 2.24 2.40 ko +0.0/-0.1 3.70 1 w f p +/- 0.05 +/- 0.1 +0.3/-0.1 5.50 8.00 12.00 ao 3.70 +/- 0.1 bo +/- 0.1 cathode side anode side copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds
13 packaging patent label (on bottom of box) label with cree bin code, qty, reel id label with cree bin code, qty, reel id label with cree order code, qty, reel id, po # label with cree order code, qty, reel id, po # label with cree bin code, qty, reel id unpackaged reel packaged reel boxed reel cree bin code & barcode label vacuum-sealed moisture barrier bag label with customer p/n, qty, lot #, po # label with cree bin code, q t y , lot # label with cree bin code, q t y , lot # v acuum - sealed moisture barrier bag p atent label label with customer order code, q t y , r eel i d , po # copyright ? 2012-2014 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? , the cree logo and xlamp ? are registered trademarks of cree, inc. xlamp ? XP-G2 leds

▲Up To Search▲

Price & Availability of XP-G2

	To Download XP-G2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .